Keyence PX-10 Uživatelský manuál stáhnout pdf

Heavy-duty Photoelectric Sensor

PX-10(P)/10C(P)

Instruction Manual

Part Names

Ampliﬁer Unit

There are two types of ampliﬁer units.

•

PX-10/10P (above): Uses a cable length of 2 m and can handle external input.

• PX-10C/10CP (connector type): Connects to the power source with a socket cable.

Input/Output Circuit

■PX-10 (NPN output)

■PX-10P (PNP output)

■PX-10C (connector type NPN output)

■PX-10CP (connector type PNP output)

● Socket Cables for PX-10C/10CP (Optional)

■OP-75721 (cable length 2 m) ■OP-75722 (cable length 2 m)

■Relationship between connector pin numbers and cable core wires

Information in the following table is the same for OP-75721 and OP-75722.

Note

When connecting the L-shaped cable (OP-75722) to the ampliﬁer unit, face the

connector for the cable towards the ampliﬁer unit in the direction shown in the following

diagram and lock it into place. Note that the connector portion cannot be reversed.

Precautions on Installation

●

Connecting the Sensor Head to the Ampliﬁer Unit

Note

• The sensor is not guaranteed under the conditions of the warranty if the sensor head

is not connected correctly using the procedure described above.

• The sensor is not guaranteed under the conditions of the warranty if dust or dirt

attaches to the packing for the sensor.

• If the sensor head cannot be inserted easily, fully remove any dirt or dust from the

ampliﬁer unit and apply silicon grease to the opening.

1 Grasp the cap for the sensor head connector and insert the connector straight

in the direction shown in the diagram.

SET

UP/DOWN

MODE

DSC indicator

Operation status indicator

(detection output)

Operation status indicator

(alarm output)

Digital monitor

Head release lever

button

SET

buttons

UP/DOWN

button

MODE

Head installation

holes

Sensor head connector

receptacle

Load

0 V

12–24 V DC

Brown

White (Alarm output)

Light sensor circuit

5–40 V DC

Overcurrent

protection circuit

Blue

Black (Detection output)

Load

3.3 V DC

Blue

Pink (input)

(Short-circuit current

1 mA max.)

PLC, etc.

0 V

Main sensor circuit

0 V

12–24 V DC

Brown

White (Alarm output)

Light sensor circuit

Blue

Black (Detection output)

Load

Overcurrent

protection circuit

Load

Brown

Pink (input)

(Short-circuit

current

2 mA max.)

PLC, etc.

12–24 V DC

Main sensor circuit

Load

0 V

12-24 V DC

Pin q

Pin w (Alarm output)

Light sensor circuit

5-40 V DC

Overcurrent

protection circuit

Pin e

Pin r (Detection output)

Load

Connector

pin position

0 V

12-24 V DC

Pin q

(Alarm output)

Light sensor circuit

Pin e

Pin r (Detection output)

Load

Overcurrent

protection circuit

Load

Connector

pin position

Warning

• This product is used to detect targets. Do not apply the product to

safety circuits for human protection.

• This product is not of explosion-proof construction. Do not use the

products in places with ﬂammable gas, liquid, or dust.

• This product is a sensor of DC power supply type. Do not apply

AC power. Application of the AC power may lead to explosion or

ﬁre.

Connector pin no. Wire casing color Connection

①

Brown 12 to 24 V DC

②

White Alarm output

③

Blue 0 V

④

Black

Detection output

Connector

pin position

Amplifier unit

Sensor head

connector

Hold the cap by

the sides.

96M1591

1 2 3 4 5 6 7 8 9 10

Shrnutí obsahu

Strany 1 - Instruction Manual

1Heavy-duty Photoelectric Sensor PX-10(P)/10C(P)Instruction ManualPart NamesAmpliﬁer UnitThere are two types of ampliﬁer units.• PX-10/10P (above): Us

Strany 2 - Ampliﬁer Unit

Strany 3 - Fine-adjusting Sensitivity

2 2 Insert the two upper tabs on the mounting ﬁxture into the head installation hole on the ampliﬁer unit and pull the mounting ﬁxture up in the dire

Strany 4 - Selecting Detection Mode

3 Setting a Sensitivity – Basic – ● Improving Performance against Dust and Stains (Maximum Sensitivity Setting) Set the sensitivity without a workp

Strany 5 - Correcting Display Values

4 Selecting Detection Mode Detection mode can be set for normal detection or for one of the following two modes. ● Edge Detection Mode (Page 6, No. 5

Strany 6 - Setting Each Type of Function

5Display Selection when Running Detection● Display Selection (Page 7, No. 10)The display selection can be changed in the following manner during detec

Strany 7 - Outputting Alarms

6Setting Each Type of FunctionNormally, only standard settings can be used.Display each type of menu and change the settings as required.•Press and ho

Strany 8 - 4 Remove the cables

7System Settings Menu● Initializing, Saving, and Loading Settings Initializing settings (returns the parameters to the factory default state)1 While p

Strany 9 - Mounting the Connector

8Shortening the Sensor Head CableBe sure to follow the steps carefully in order to waterproof the cable. Sensor head connectorDisassembled diagram (co

Strany 10 - Warranties and Disclaimers

9Connecting the Cables and the IDC ConnectorNoteWhen the cable length of the sensor head is changed, be sure to connect the ampliﬁer to check that it

Komentáře k této Příručce

Žádné komentáře

Keyence PX-10 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Senzory Keyence PX-10. KEYENCE PX-10 User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Senzory Keyence PX-10