Keyence DL-RS1A/IG Uživatelský manuál stáhnout pdf (Strana 16)

Parameters of Commands and Responses

115 Sub display's screen * 1 R/W

0: R.V. value screen

1: Analog output screen

2: HIGH setting value screen

3: LOW setting value screen

4: Shift target value setting screen

5: Calculated value display screen

116

Tolerance tuning Tolerance

setting width*

**.*** 6 R/W 00.000 to 99.999 00.100

117 Calibration function SET1 ±**.*** 7 R/W -99.999 to +99.999 +00.000

118 Calibration function SET2 ±**.*** 7 R/W -99.999 to +99.999 +05.000

119 Calibration Function * 1 R/W

0: Standard

1: User setting

120 System parameter*

** 2 R/W 0 to 15 00

129 Calculation function*

*1R/W

0: The calculation function is not used.

1: Addition mode

2: Subtraction mode

3: 2 Heads mode

130 Measurement mode * 1 R/W

0: Edge control/Positioning mode

1: Outer diameter/Width measurement mode

Inner diameter/Opening measurement mode

3: Glass edge mode

4: Pin position measurement mode

5: Pin interval judgment mode

6: Pin diameter judgment mode

Specified edges interval measurement mode

131 Measurement direction * 1 R/W

0: Top

1: Bottom

132 Averaging*

** 2 R/W

0: hsp

1: 1

2: 2

3: 4

4: 8

5: 16

6: 32

7: 64

8: 128

9: 256

10: 512

11: 1024

12: 2048

13: 4096

133 Output mode * 1 R/W

0: NO (Normally Open)

1: NC (Normally Close)

134 Hold function setting * 1 R/W

0: Sample hold

1: Peak hold

2: Bottom hold

3: Peak-to-peak hold

4: Auto peak hold

5: Auto bottom hold

135

Auto peak hold or Auto bottom

hold Trigger level*

±**.*** 7 R/W -99.999 to +99.999 +00.100

136 Timing Input * 1 R/W

0: Level

1: Edge

137 Delay Timer * 1 R/W

0: Delay timer off

1: On delay timer

2: Off delay timer

3: One shot timer

138 Timer value **** 4 R/W 1 to 9999 0060

139 Hysteresis*

**.*** 6 R/W 0 to 99.999 00.010

140 Analog Output Scaling * 1 R/W

0: Initial state

1: Free range

141 Analog output Lower limit*

±**.*** 7 R/W -99.999 to +99.999 +00.000

142 Analog output Upper limit*

±**.*** 7 R/W -99.999 to +99.999 +10.000

143 External input*

*1R/W

0: Initial state

1: User setting

Data

No.

Data name

Data

format*

No. of

bytes

Attribute*

Data range Default value

Parameters of Commands and Responses

*1 In the Data format column, "±" indicates that the value can be either "+" or "-" and "*" signifies a

number from "0 to 9".

*2 Indicates that the data can only be read from (R), can only be written to (W), or can be both read

from and written to (R/W) the sensor amplifiers.

*3 The command is executed only when the data is changed from 0 to 1. To re-execute the

command, first change the setting to 0, then change it to 1. Otherwise, the command is not

executed.

If the sensor amplifier is turned OFF after the standard waveform registration is performed, the

previous state before the standard waveform registration is performed is restored. If you wish to

keep the standard waveform registration even after the power is turned OFF, set the saving the

standard waveform function to ON.

If the sensor amplifier is turned OFF after the zero shift is performed, the previous state before

the zero shift is performed is restored. If you wish to keep the zero shift state even after the

power is turned OFF, set the saving zero shift value function to ON.

144 External input 1*

*1R/W

0: Zero shift input

1: Bank A input

2: Bank B input

3: Laser emission stop input

4: Not use

145 External input 2*

*1R/W

0: Reset input

1: Bank A input

2: Bank B input

3: Laser emission stop input

4: Not use

146 External input 3*

*1R/W

0: Timing input

1: Bank A input

2: Bank B input

3: Laser emission stop input

4: Not use

147 External input 4*

*1R/W

0: Gain input

1: Bank A input

2: Bank B input

3: Laser emission stop input

4: Not use

148

Saving the standard waveform

function

*1R/W

0: OFF

1: ON

149 Saving zero shift value function * 1 R/W

0: OFF

1: ON

150

Interference prevention

function*

*1R/W

0: OFF

1: ON

151 Display Digit * 1 R/W

1: 0.001

2: 0.01

3: 0.1

4: 1

152 Power save function * 1 R/W

0: OFF

1: Half

3: All

153 Position monitor * 1 R/W

0: Initial state

1: OK/NG display

2: Red OFF

3: OFF

154 Display color * 1 R/W

0: GO Green

1: GO Red

2: Always Red

155

Edge check function Number of edges

** 2 R/W 0-99 01

156 Edge check function * 1 R/W

0: OFF

1: Setting A

2: Setting B

Data

No.

Data name

Data

format*

No. of

bytes

Attribute*

Data range Default value

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 27 28

Komentáře k této Příručce

Žádné komentáře

Keyence DL-RS1A/IG Uživatelský manuál Strana 16

Komentáře k této Příručce

Související produkty a manuály pro Senzory Keyence DL-RS1A/IG